Archive for the ‘Heating’ Category

« Older Entries

What Huntington Beach Residents Should Do If Their Furnace Keeps Turning On and Off?

Monday, April 16th, 2012

Furnaces in Huntington Beach are designed to last decades without major problems so long as they are regularly maintained.  They typically work so well, in fact, there is a danger of taking our comfort for granted and skipping the annual furnace maintenance for a year or two as time rushes by, waking up suddenly and brutally to a dark night and no heat.

In retrospect, a preliminary indication of trouble could have been the furnace continually turning off and on in short bursts, something that was tugging at your senses, but not strongly enough to really catch your attention.

Possible Problems

A furnace constantly turning on and off could often be a direct result of poor airflow through the system.  Heat builds up and the detectors sense the proper temperatures have been reached and automatically shut down.  In the room, the thermostat calls for more heat and starts the cycle over again.

A relay switch or control valve may also be worn and working improperly.  A crack in the heat exchanger might fuel the flame to burn too hotly and cause the sensor to misinterpret the information and shut down.

These problems not only impede the distribution of heat to the living spaces, decreasing comfort, but also create intense wear on the motor and controls, threatening the very life of the appliance.

Simple Solutions

Restricted airflow can be caused most often by a dirty or clogged filter.  At the furnace, there is usually a panel that can be removed to check, clean or replace the filter.  It is typically a single or series of cardboard and screen panels approximately 1′ by 2′, but varies by manufacturer and furnace output.

A vacuum to pull lint free or compressor to blow it clean are the recommended tools to use a few times each year.  It is a good idea to change the filters at the beginning of each heating season. The belts are also easily replaced.

The fan belts for the blower may also be worn loose and not pushing the air hard enough to get through the filters.  It is a good idea to check them regularly as well.

The Calvary Charge

When in doubt, call Saddleback Plumbing.  Scheduling an annual inspection and service with us takes the worry out of living in a furnace heated home.  Besides the rite of safe passage for your peace of mind, trained mechanics can spot the defects and give you the best assurance of a long life of comfort and warmth.

When contracting with the same HVAC company over time, a relationship is built whereby they care nearly as much as you.

Tags: , ,
Posted in Furnace Maintenance, Heating, Huntington Beach Furnace | Comments Off

Heat Pump Air Duct Requirements in Orange County

Monday, April 9th, 2012

The concerns about climate change and the rising costs of energy production has inspired a lot of experimentation with new technologies in Orange County heat pumps.  Standard choices are being re-evaluated and new designs are changing the requirements for various parts.

In homes and other buildings where heating systems were designed and installed according to the cheaper energy parameters prevalent in the day, it may be time to consider drastic changes to increase the efficiency and decrease impact on the carbon footprint.  Room for improvement can be found in many corners.

Heat Pump Technology

Among the systems getting a fresh look are heat pumps, a device that transfers thermal energy from one location to another, usually in the direction of from a colder temperature to higher and generally the opposite of the natural flow.  While compressor-driven air conditioners and freezers are technically heat pumps, “heat pump is the term that usually implies one of the less-common devices in the class that are not dedicated to refrigeration-only.

A heat pump that maintains a thermally conditioned-space can be used to provide either heating or cooling, depending upon whether the environment is cooler or warmer than the conditioned-space.  Typically pumps utilize some thermal energy from the environment itself, such as the natural heat beneath the Earth’s surface.

By simply transferring the energy rather than producing it, heat pumps are being more seriously considered as attractive alternatives to provide an efficient and clean system for conditioning public and living spaces.

Change of Use

In considering a change from an existing system to a heat pump, there are many details to compare to see if it makes any sense at all.  The overall local climate (cool or hot) in general, and the availability of geothermal heat, in particular,  are two major factors.

Since a heat pump typically moves conditioned air through ductwork, the advantages of the change are much more realistic with a system of pre-existing ducts such as a forced air furnace or central air-conditioning unit.  While a heat pump often requires a larger volume of ducts, the old network of metal tunnels was often over-sized for inefficient furnaces and should do fine in a conversion to a heat pump.

The Right Data

Since the required formulas are dependent upon variables such as size, distance, volume and oomph, the design is strategic and makes all the difference.  Contact Saddleback Plumbing to speak with a trained and experienced professional because.

Do the homework to get the best recommendation for your home.

Tags: , ,
Posted in Heat Pumps, Heating, Heating Systems | Comments Off

Corona Del Mar Heat Pump FAQ: Why is Steam Rising from the Outdoor Unit of my Heat Pump?

Wednesday, March 28th, 2012

In the winter months, we often get calls from Corona Del Mar customers about steam rising from the outdoor unit of their heat pumps, which is often mistaken for smoke. Steam rising from your outdoor unit is a normal during the heat pump defrost cycle. The defrost cycle prevents ice from accumulating on the outdoor coils.

Under normal conditions, heat pumps in Corona Del Mar should run without needing a defrost cycle. However, if temperatures drop to near freezing, a sensor will set off the defrost cycle, during which the outdoor coils will heat up and melt any ice that has formed on the coils. During this cycle, you may see what can look like puffs of smoke, but it’s actually the steam caused by the coils melting the frost. The steam can appear to be denser if there’s excessive humidity or moisture in the air.

It is important to note that the defrost cycle should not last more than ten to fifteen minutes, and each cycle should only run every two hours or so. If you notice that the cycles last longer, run more often, or if you see ice on the outdoor coils of your heat pump after the cycle is finished, you may need a heat pump repairs. Another concern is cooler temperatures in your home, which could indicate that the heat strips are not working properly during the defrost cycle.

Once the cycle is finished, the fan motor should come on again, but if it doesn’t come on several hours after the cycle, you should call us to send one of our HVAC technicians to inspect your heat pump. There could be an issue with airflow, or a potential motor failure. When there’s a lack of adequate airflow, it can damage the compressor and other components. Call us any time you notice anything other than the normal steam rising from your heat pump during the winter.

There are some ways to prevent excess wear and tear on your heat pump during the winter. For instance, strong winds can greatly affect the performance of your heat pump and may cause abnormal defrost cycles. Make sure the outdoor components are protected from heavy wind by placing some type of natural or manufactured barrier around your heat pump, but be sure not to block the airflow. If you are buying a new heat pump, look for a model that has demand-defrost control. This feature helps to save energy by minimizing the defrost cycles.

Feel free to call Saddleback Plumbing if you have questions about your heat pump or Corona Del Mar heating.

Tags: , ,
Posted in Heat Pump Repairs, Heat Pumps, Heating | Comments Off

Why Orange County Residents Should Get a Energy Audit Before Installing a New Heating Upgrade

Wednesday, March 21st, 2012

Yesterday was the first day of spring, so if you can’t feel it already, warmer temperatures are on their way to Orange County.  When you envision the warm days of summer, do you picture staying cool with an energy efficient cooling system, without any worries about high energy costs?  Or are you concerned that your older air conditioning unit won’t make it through another hot summer?  Well right now is the perfect time for an air conditioning installation, not only because Saddleback Plumbing can save you money on your purchase, but because there have been so many upgrades to the technologies of cooling systems.

Before you take the plunge on new equipment, though, you may want to get a home energy audit. What you find may help you choose the right system.

A home energy audit is essentially an inspection by a professional of the materials used to insulate your home. This includes not just the insulation in the walls, but also the walls themselves, along with windows, doors and so on. The idea is to figure out how much heat is escaping your home to the outside, so an audit may also include looking at ducts, vents or anywhere else where air could flow through.

So what does an energy audit have to do with a heating upgrade?

Think about it like this. There are two ways to make your home warmer: increase heat gain (e.g., get a more efficient heating system) or decrease heat loss. If you are able to do the latter, you may find that the former is unnecessary.

For example, you may get an energy audit and discover that by installing new windows and resealing your doors, you can increase heating efficiency by 10%. This could have big implications for your decision to get a new heating system, as you may decide that you can save money by getting a smaller capacity furnace. Getting the right size furnace is very important; one that is too small will not be able to heat your home to the desired temperature and one that is too large will short-cycle, which leads to uneven heating and wears down your system quickly.

A home energy audit is the first step to getting a new heating system, and one that is sure to save you money. Give Saddleback Plumbing a call to set up an energy audit today!

Tags: , ,
Posted in Air Conditioning, Air Conditioning Installation, Heating | Comments Off

Orange County HVAC Tips: The Differences Between SEER and HSPF Ratings

Wednesday, March 7th, 2012

When it comes to heat pumps in Orange County and across the country, there are two different ratings you’ll often see – the SEER and the HSPF. So, what does each of them mean and which rating is more important when purchasing your new device? Here are a few things to consider:

SEER

The acronym SEER is short for “seasonal energy efficiency rating” and is used most commonly to measure air conditioner efficiency or in this case, the cooling capacity of your heat pump.

HSPF

The HSPF is short for “heating seasonal performance factor” and is a measurement of how efficient the heat pump is in producing heat during the cooler months of the year.

The Difference Between the Two

Every heat pump will have both of these ratings, allowing you to see how efficient each is. This is important because you need to know for certain how well your heat pump will perform under certain situations – both in the winter and summer.

However, if you live in a colder climate where the summer rarely calls for air conditioner, your focus should be on the HSPF first. And if you live in a warmer climate where your heating needs are minimal, the SEER is most important. Another thing to consider is your supplemental heat. If the cost of your supplemental heating system is high, you’ll want an HSPF that is as low as possible to balance it out.

Choosing an Efficient Heat Pump

Heat pump efficiency directly impacts the price of the device you purchase but is almost always worth the difference. The key is to find a device that provides what you need based on where you live. Keep in mind as well that, like most HVAC upgrades, you won’t immediately recoup the cost of the device in your energy savings, so if you plan on moving soon, you should purchase a more affordable device now and upgrade later.

Purchasing a heat pump is an important step in making your home more energy efficient. If you are unsure which rating you need or how to analyze their meanings, contact Saddleback Plumbing to learn more.

Tags: , ,
Posted in Air Conditioning, Heat Pumps, Heating | Comments Off

What Dana Point Residents Can Do When a Heat Pump Isn’t Operating Properly

Wednesday, February 8th, 2012

A heat pump in Dana Point is designed to provide steady, reliable heat in your home throughout the year. So, what do you do when your heat pump suddenly stops producing enough heat? The first step is to figure out why exactly your heat pump has stopped working properly. From there, you can take action to get it back on track.

Reasons Your Heat Pump Isn’t Producing Heat

There are a number of reasons a heat pump might stop producing enough heat. Here are some of the most common ones you’ll encounter:

  • Too Cold Outside – A heat pump can only handle temperatures so low. Most heat pumps are rated for outside temperatures as low as 40 degrees F (though they work best at 50 degrees F and up). If the outside temperature gets below the 37 degree F mark, it’s likely the system won’t be able to produce enough heat. Remember, however, that you should have an emergency heat source. If it isn’t on but the outside temperature is below 37 degrees F, you may have a problem with the outdoor thermostat or emergency switch.
  • Fans – The fans on your heat pump may not be working properly. Simply check this by increasing the thermostat setting on your heat pump. If the fan never comes on, there could be an electrical or mechanical problem in your fan.
  • Thermostat Readings – A simple problem that can stall your heat pump is thermostat failure or calibration problems. Check the thermostat to see if it is working properly and if not, call a professional.
  • Refrigerant – If the refrigerant gets low in your heat pump, you may need to have it recharged. This is a quick and relatively inexpensive process so call for professional assistance as soon as you notice the problem.

If your heat pump isn’t working properly, don’t wait for it to break completely or for the temperature outside to become unbearable. Contact Saddleback HVAC experts for help immediately and get your heat pump fixed before it’s too late. Even a seemingly simple problem can quickly turn into a major issue if it isn’t dealt with immediately.

Tags: , ,
Posted in Heat Pumps, Heating, thermostat | Comments Off

What to do Before Turning on AC for First Time in Orange County

Wednesday, February 1st, 2012

The weather is starting to heat up in Orange County and you are eager to flip the switch on your air conditioning system for the first time. It’s been sitting there, waiting to be used, but now you wonder if there are any tasks that should be completed before its first use. Depending on the type of system you had installed there are a few things you should keep in mind before you cool down your house. They include:

  • Outdoor Cleaning – First, make sure the outdoor unit (if you have a central AC system) is cleaned up nicely. Clear away any leaves, remove the cover and check the system for any growth or debris that might have gotten under the cover. Check the air supply registers to make sure they are open and either replace or clean your filters depending on whether they are permanent or disposable.
  • Check Your Thermostat – The thermostat should be checked before you start using the system. To do this, set the system to Auto-cool and then lower the thermostat setting to one degree lower than the actual temperature in the room. If the system turns on, the thermostat is working properly. Let it run for a few hours to make sure this stays consistent.
  • Clear Away Winter and Spring Dust – Now that your system is running, make sure you check the filters for any buildup of dust that was in the ductwork. Over the off season, your ducts might develop a layer of dust and debris, especially if your heating system doesn’t make use of them. The filters might clog quickly as a result.
  • Check for Water Leaks – Your condensate overflow drain should work properly as well – check for any potential leaks during the first 48 hours of operation. Even a small leak should be checked immediately to avoid potential problems as summer cooling season kicks in.

If you notice any problems other than those listed above, you should call a service professional immediately. Ideally you will have your system inspected in early-mid spring to ensure it is ready for the summer, but even so problems can develop between inspection and first running. Electrical issues especially should be checked immediately.

Tags: , ,
Posted in Air Conditioning, Air Conditioning Repair, thermostat | Comments Off

Irvine Plumbing Q/A: Why Won’t My Heat Pump Start?

Monday, January 30th, 2012

Plumbing experts in Irvine advise home owners that if you are having trouble with your heat pump, you may be surprised to learn that it is probably not the heat pump that is to blame, especially if the trouble is that it simply won’t start up. That seems counterintuitive, but it’s true: the heat pump can be in perfect working order but still not turn on.

The good news, then, is that your heat pump is fine and you won’t have to pay an arm and a leg to fix or replace it. Still though, these types of problems can very frustrating to diagnose and correct. Here are four common culprits when a heat pump won’t start:

  1. No power to the heat pump. Check your breaker box to see if the circuit breaker was tripped. If so, reset it and see if that fixes the problem. Another possibility is that your heat pump is wired to a wall switch, or that there is a switch on the unit itself. Make sure the switch is turned on.
  2. Make sure the thermostat is set to the proper mode, such as “heat” mode if you desire more heat. It seems overly simple, but sometimes the trouble is as simple as that.
  3. A recently replaced thermostat. If you recently upgraded or replaced the thermostat in your home, it’s possible that something went wrong that is preventing your heat pump from starting. It may be the wrong kind of thermostat – heat pumps require a specific type – or it may have been improperly wired.
  4. Finally, the heat pump may have its own circuit breaker on the air handler cabinet. This is often the case with heat pumps that have supplemental electric elements. If that breaker is tripped, that could cause the problems you are experiencing.

If you exhaust these problems and the problem persists or recurs – for example, if the circuit breaker trips again – call a contractor to work on your heat pump. There may be something larger at work that is causing problems in the electrical system that controls your heat pump, and that requires some expertise to properly address.

Tags: , ,
Posted in Heat Pumps, Heating, thermostat | Comments Off

Santa Ana Heating Replacement Tip: Signs of an Undersized Furnace

Monday, January 23rd, 2012

If you’re purchasing a new furnace for your Santa Ana home, you want to avoid buying one that is undersized for your particular space. To do that, here are some common signs that the furnace isn’t powerful enough for the heating needs of your home. These signs might appear for an older furnace as well, especially as it ages and loses its ability to provide adequate heat for your home.

Maintaining Temperature

The most common (and in many cases only) sign that your furnace is undersized is that the device simply doesn’t maintain the temperature in your home properly. This means that when turned on to full and left for a few hours, your furnace doesn’t heat your home to the thermostat setting.

This can be due to an improper load calculation or a load calculation that wasn’t taken at all. The perfectly sized furnace will heat your home evenly on the coldest day your area is likely to have. So, undersizing should be pretty evident – if it doesn’t heat your home evenly and it’s not exceptionally cold outside, you might not have enough BTUs under the hood.

How to Fix the Problem

The problem is one that varies depending on the severity of the undersizing. Modern furnaces are often available with two stages, meaning they can operate at both a low BTU rating (often around 40K or so) and a higher BTU rating (70K or higher). This is the perfect solution for homeowners worried about undersizing because it ensures that your home always has enough heat in reserve should the weather get exceptionally cold.

For example, most furnaces are sized for extremely low temperatures, but if the temperature jumps up to 50 degrees F outside, your furnace is now oversized for that weather. A two stage furnace offers solutions for both common conditions and extreme conditions and will resolve most of the concern you have about undersizing and not having enough heat to offset outdoor temperatures.

Tags: , , , , , ,
Posted in Heating | Comments Off

Dana Point Heating Maintenance: Basic Furnace Safety Tips

Friday, January 20th, 2012

While you should schedule a yearly maintenance visit with a qualified HVAC technician to check for any safety concerns, you can also reduce potential safety hazards in the heating system of your Dana Point home. Whether you have a furnace or a heat pump, you can substantially decrease the chances of dangerous situations with a few minor routine tasks.

If you have any questions about how to better maintain your heating system, give us a call to speak with one of our expert HVAC technicians. Here are a few guidelines to get you started.

Ventilation in Forced-air Systems:

  • Regularly vacuum and clean out your heating vents and fan blower.
  • Check the condition of your chimney and vent pipe to make sure that none of the parts are damaged or show signs of deterioration.
  • Test the thermostat occasionally to make sure your heating system is working at optimal levels. There could be a safety concern if your heater is not properly heating your home.

Heat Exchangers:

  • Heat exchangers should be inspected often to prevent carbon monoxide leaks. Check for any obvious issues, such as rust or other damages.
  • The heat exchanger for furnaces should be inspected by a professional once a year in case there are hidden problems with the equipment, or if any of the components need to be replaced.
  • Check the pilot light in gas furnaces for any flickers or changes in color. Have someone turn up the thermostat while you watch the light, but turn off the system for five minutes first. If there are any changes, there could be a problem with the heat exchanger. Call a professional if you suspect issues with your heat exchanger.

Heating Equipment Inspections and Adjustments:

  • Adjust the temperature settings if you suspect that the heater isn’t working properly, and if it doesn’t work call a professional heating technician, or if you aren’t sure how to locate or adjust the controls.
  • Check the overall equipment for cracks, rust, or any other obvious signs of damage or deterioration that could create safety hazards.

In addition to performing these tasks, call a licensed Dana Point heating contractor to inspect your heating system at least once a year.

Tags: , , , , ,
Posted in Heating | Comments Off

« Older Entries